AUTOMATIC JR CENTERING SYSTEM
AUTOMATIC JR CENTERING SYSTEM
This option makes it possible to rewind film exactly at the core center without attendance of an operator.
The system monitors the rewinded film edge and moves the JR feeder in the corresponding direction.
ADVANTAGES:
Marketable appearance of the roll
Decrease of labor content due to the process automation
JR ENDING MONITORING SYSTEM
JR ENDING MONITORING SYSTEM
The system is used to timely stop rewinding process when minimal amount of the film remains on the JR (minimal outer JR diameter).
This criterion is checked by an optic sensor by means of a special mark. When the sensor detects the critical value, the rewinding process is stopped. After that, the operator can replace the JR and finish rewinding at minimal speed.
This makes it possible to finish the process without rejection of the roll due to improper film length.
ADVANTAGES:
Decrease of rejected roll quantity
Increase of production efficiency
Time savings due to elimination of necessity to rethread the film
FILM BREAK MONITORING SYSTEM
FILM BREAK MONITORING SYSTEM
If the film breaks, the rewinding process is stopped automatically. The sensor measures the length of already wound film and displays the corresponding notification message. After rethreading, the system recalculates the length (weight) still to be wound, which allows the machine to rewind the target length or weight of the film.
ADVANTAGES:
Decrease of production waste quantities
Elimination of prolonged delays due to fast response to the abnormal situation
FILM WOUND ON DRUM DETECTION
MONITORING SYSTEM OF FILM WOUND ON THE DRUM
In case of unintended film winding on the drum, the machine stops automatically, and the corresponding notification message appears on the screen
ADVANTAGES:
Decrease of production waste quantities
Prevention of mechanical failures of the machine components caused by accidental film winding on the drum
Time savings due to elimination of necessity to remove the film from the drum
REVERSE REWINDING FUNCTION
REVERSE REWINDING FUNCTION
This function makes it possible to wind the film off the JR if it was wound on the drum.
ADVANTAGES:
Decrease of production waste quantities
Prevention of mechanical failures of the machine components caused by accidental film winding on the drum
Prevention of mechanical failures of the machine components caused by film removal from on the drum
Time savings due to elimination of necessity to remove the film from the drum
REWINDING WITH PRESET LENGTH
REWINDING WITH PRESET LENGTH
This mode makes it possible to rewind finished rolls with preset length of the film.
ADVANTAGES:
High rewinding precision: length error does not exceed 1 m.
REWINDING WITH PRESET WEIGHT
REWINDING WITH PRESET WEIGHT
This mode makes it possible to rewind finished rolls with preset (gross) weight.
ADVANTAGES:
High rewinding precision: weight error does not exceed 15 g.
FISCAL COUNTER
FISCAL COUNTER
The fiscal counter counts the finished rolls and stops the machine as soon as the target number of them is wound. The operator sets the necessary finished roll quantity in accordance with his job order.
Upon completion of the task, the machine stops and the corresponding notification message appears on the controller display.
ADVANTAGES:
Process automation
High equipment precision
Elimination of prolonged delays due to fast response to the task completion
EXTENDED ENGINEERING MENU
EXTENDED ENGINEERING MENU FOR TECHNICAL PROFESSIONALS
The extended engineering menu is intended for troubleshooting and setup of the equipment. The control system interface is divided into the following access levels:
1. The first access level for operators
2. The second access level for technical professionals
ADVANTAGES:
Quick troubleshooting (in/out menu)
Convenient equipment change-over to another raw material type (manual debugging mode)
Control at different access levels
MULTILINGUAL CAPABILITY
MULTILINGUAL CAPABILITY
The multilingual controller capability makes it possible to select a necessary interface language. The basic menu configuration supports 10 languages. If necessary, customers may request the manufacturer to translate the interface to a new language.
ADVANTAGES:
Prevention of improper setup of the machine parameters
Comfortable and safe operator’s activity
Possibility of switching to various languages
TABLE FOR FINISHED ROLLS
STACKING TABLE
The stacking table is designed for collecting and stacking finished rolls. Thanks to this feature, the operator has no need to extract and transfer the rolls to the hopper/container as soon as the cycle is over.
ADVANTAGES:
Comfortable operator’s activity
CORE BUSHINGS FOR DIFFERENT IDS
CORE BUSHINGS FOR DIFFERENT IDS
The kit includes plugs 25 to 76 mm in diameter.
This kit is essential if the Customer intends to use variable diameter cores for production.
We can manufacture unique diameter cores customized to your needs
ADVANTAGES:
Extended assortment of finished products
SHOW/HIDE ALL